BD-5800H,This External Modulated Optical Transmitter is a 1550nm DFB laser optical transmitter. It is specially developed for the CATV signal that satisfies HFC network, and the long-distance transmission of cable phone and cable data.
It has 7 function modules: RF control, DFB laser, optical modulator, SBS control, CSO control, communication/display control and power supply.
Automatic gain control circuit (AGC) or manual gain control circuit (MGC) amplifies the RF signal. AGC or MGC control makes the optical modulator maintain a suitable input level. Use the detected RF root-meansquare (RMS)-total power to calculate the optical modulation index (OMI).
In general we recommend using the AGC function, and special users can use the MGC function to adjust the CNR/CSO/CTB performance indexes.
The core of transmitter is the optical modulator. The 1550nm signal input the optical modulator, make the laser intensity changed follow the external RF signal voltage, and then generate the AM optical signal.
Stimulated Brillouin Scattering (SBS) occurs, when the optical input power is greater than a certain threshold value. SBS generate the lower frequency backscattered light which will attenuate the transmission light and return to the laser while destroying its performance. Causing optical power fluctuation, generates large noise, and seriously deteriorates the system carrier to noise ratio (CNR). To improve the SBS threshold, this optical transmitter adopts SBS control technology which is independent researched and developed by ourselves. The threshold value can be set up to 19dBm.
The optical modulator has a two-way optical signal output. Parts of that signal are routed to an InGaAs photodiode. This detection of the optical signal has two functions:
1) Detect whether the laser is normal working. Once the output optical power is 2dB lower than standard power, alarm will be set off.
2) Detect CSO distortion to optimize the bias point of the optical modulator. For working normal the detector circuit needs at least two carrier signal inputs with an interval of 24MHz. There is a CSO initialization program in the boot process. If the CSO install failed, the RF indicator will flash red, see details in 6.2 Troubleshooting.
|Optical Wavelength||nm||1545～1560 (or specified by the user)|
|Side-mode Suppression ratio||dB||>30|
|Relative Intensity Noise||dB/Hz||<-160|
|Wavelength Adjustment Range||GHz||+/-50GHz|
|Optical Power||dBm||2*5, 2*7, 2*8, 2*9, 2*10|
|SBS Threshold Value||dBm||+13～+19 (Continuously adjustable)|
|RF return loss||dB||>16|
|RF input impedance||Ω||75|
|RF input connector type||F type|
|Rated input level||dBµV||80|
|Input level range||dBµV||78~96 (AGC mode, modulating signal)|
|AGC control range||dB||+3～-3|
|MGC adjustable range||dB||0~15|
|Optical connector||SC/APC, FC/APC|
|Power Source Specification||V||90～265VAC|
|Dimension||mm||483(L) × 455(W) × 44(H)|
Panel Interface and Menu System Description
|1||Power indicator||2||AGC indicator||3||RF modulation degree indicator|
|4||Laser indicator||5||LCD||6||ESC key|
|7||UP key||8||DOWN key||9||Enter key|
|10||RF input port (or on the rear panel, optional)||11||-20dB RF input test port|
|1||Ground stud||2||Power module||3||Fan|
|4||RF input port (or on the front panel, optional)||5||RS232 interface||6||LAN interface|
|7||Optical output interface A (or on the front panel, optional)||8||Optical output interface B (or on the front panel, optional)|
220V Power Module
|1||Mounting screws||2||220V power outlet||3||Fuse|
48V Power Module
|1||Mounting screws||2||+ Positive terminal block||3||– Negative terminal block|
- High-performance long-distance transmission
- High-power distribution network
- Redundancy loop architecture
- FTTx network
- RFOG application
- DWDM network
WEB Network Management
Open the IE browser, type the IP address and enter the interface as follows:
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.